Three Beeps — on power up If the scanner beeps 3 times on power up then the non- volatile memory NovRAM that holds the scanner configuration has failed. If the scanner does not respond after reprogramming, return the scanner for repair to an authorized service center. Page Upgrading The Flash Rom Firmware The user merely connects the scanner to a communications port of the PC, launches the MetroSet 2 program, and blasts off to new software upgrades.
Each MS and its cradle, regardless of the version number or communication protocol, can be upgraded. This label has the model number, date of manufacture, serial number, CE and caution information. Page Connecting To Other Bluetooth Devices A Bluetooth communication between the scanner and the other device must be established before the system works.
Communication is established by scanning the Bluetooth address code of the other device. This will allow other Bluetooth devices to send inquiries to the scanner and attempt communication. Make sure the cable is plugged into the cradle properly. Place the scanner into cradle to recharge the battery. Establish communication between scanner and cradle before scanning a normal bar code Verify correct country code and data formatting are selected. Adjust inter-character delay symptom. Page 35 Try operating the scanner in Alt mode.
Check to make sure that the baud Page Design Specifications 40 mm 1. The scanner and cradle are shipped from the factory programmed to a set of default conditions.
One is for power, and the other two are for interfaces connection. The pin RJ45 modular jack has diffent configurations for different interfaces. The MS scanners have a two 2 year limited warranty from the date of manufacture.
Metrologic warrants and represents that all MS scanners are free of all defects in Page Notices Never attempt to look at the laser beam, even if the scanner appears to be nonfunctional.
Never open the scanner in an attempt to look into the device. Doing so could result in hazardous laser light exposure. The use of optical instruments with the laser equipment will increase eye hazard. Il cliente non deve assolutamente tentare di riparare egli stesso lo scanner laser.
Non guardate mai il raggio laser, anche se credete che lo scanner non sia attivo. Facendolo potete esporVi ad una esposizione laser rischiosa. Page 50 Never attempt to look at the laser beam, even if the scanner appears to be nonfunctional.
Page 54 parts Page 56 July Printed in China 7 0 - 7 9 0 0 4 E This manual is also suitable for: Ms voyagerbt. Print page 1 Print document 56 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Disconnect the keyboard from host.
Plug the external power supply into the power jack on the bottom of the cradle. Plug the power supply into the AC outlet. The blue LED on the rear of the cradle will stay on. Connect the 6-pin Mini-DIN male connector of the keyboard cable to keyboard port on the host device.
Check the AC input requirements of the power supply to make sure the voltage matches the AC outlet. The outlet must be located near the requirement and be easily accessible. The blue LED on the rear of. In order for the Voyager BT to scan and charge properly both the power supply and the USB communication cable must be attached before the host device is turned on.
When the scanner is in the cradle and the power supply is connected to the cradle, the scanner is in a charging state. The power supply acts as the charging source not the USB communication cable. To perform normal scanning operations, it is critical to connect the USB communication cable to the cradle and the USB port on the host device. Connect the USB B type connector into the center jack on the bottom of the charger cradle. Plug the power supply into the power jack on the bottom of the cradle.
After the initial preparation charge of 3 hrs, the battery will only require. Connect the pin RJ45 male connector into the pin modular jack on the bottom of the charger cradle. T he scanner must be charged for a minimum of 3 hours before the scanner can be placed in full operation for the first time.
Connect the female DC power jack of the USB cable to the center power jack on the bottom of the charger cradle. See page 15 for complete instructions on. Communication between the Figure Full Speed USB scanner and cradle. Welcome to ManualMachine.
We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Metrologic Instruments. Trademarks Metrologic is a registered trademark of Metrologic Instruments, Inc. Introduction Product Overview Scanner Components Figure 1. RS and Light Pen 1. Turn off the host device. Plug the power supply into the AC Figure 4.
RS and Light Pen outlet. Turn on the host device. Keyboard Wedge 1. The outlet must be located near the requirement and be easily Figure 5. Keyboard Wedge accessible. Stand Alone Keyboard 1. Turn off the host system. Figure 6. Stand Alone Keyboard 6. IBM 1. The blue LED on the rear of Figure 7. IBM the cradle will stay on. The blue LED on the rear of the cradle will turn on.
Figure 8. Low Speed USB 5. Installation instructions continued on page next page. Low Speed USB 6. Figure 9. Full Speed USB 5. See page 15 for complete instructions on Establishing Bluetooth Communication between the Figure You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need. View and download manuals available only for.
Register and get 5 for free. Upload manuals that we do not have and get 1 for each file.
0コメント